preliminary series am el10 -az 10 w att | a c - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r8 1 of 3 north america only features: models single output model input voltage (vac/hz) input voltage (vdc) max output wattage (w) output voltage (v) output current max (a) maximum capacitive load (f) efficiency (%) amel10 - 3.3saz 90 - 305 /47 - 440 120 - 430 9.9 3.3 3.00 2200 74 amel10 - 5saz 90 - 305 /47 - 440 120 - 430 10 5 2.00 1000 7 6 amel10 - 12saz 90 - 30 5 /47 - 440 120 - 430 10 12 0.84 680 7 8 amel10 - 15saz 90 - 305 /47 - 440 120 - 430 10 15 0.67 470 79 amel10 - 24saz 90 - 305 /47 - 440 120 - 430 10 24 0.42 470 79 i nput specifications parameters conditions typical maximum units current 115vac 0.23 a 230vac 0.15 a inr ush current <2ms (cold start) 115vac 10 a 230vac 20 a leakage current 0.2 5 ma external fuse slow blow type 1 a input dissipation no load <0.5 w output specifications parameters conditions typical maximum units voltage accuracy 2 % line r egulation 1 % load regulation 0 - 100% load 2 % transient recovery time 500 s transient response deviation 25% load step 2 % of vout ripple & noise * 20mhz bandwidth 100 mv p - p *ripple and noise are measured at 20mhz bandwidth by u sing a 0.1 f (m/c) parallel capacitor. isolation specifications parameters conditions typical rated units tested i/o voltage 3sec 3000 vac isolation resistance >1000 m ? i/o isolation 3 000vac ? energy star compliant ? operating temp: -40 o c to +80 o c ? ultra small package ? over load, over voltage, short circuit protection ? up to 79 % efficiency
preliminary series am el10 -az 10 w att | a c - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r8 2 of 3 north america only general specifications parameters conditions typical maximum units switching frequency 6 6 khz over load protection auto recovery, fold back 150 % over voltage protection zener diode clamp short circuit protection auto recovery operating temperature with derating above 50oc - 40 to +80 o c maximum case temperature 100 o c storage temperature - 45 to +95 o c temperature coefficient 0.02 % / o c humidity non condensing 20 ~ 95 % rh case material plastic resin + fiberglass (flammabil ity to ul 94v - 0) weight 70 g dimensions (l x w x h ) 2 . 22 x 1 . 21 x 0. 9 9 inches 5 6. 48 x 30. 86 x 25 .1 0 mm mtbf > 400 000 hrs (mil - hdbk - 217f, t=+25 o c) note: all specifications in this datasheet are measured at an ambient temperature of 25c, humidit y<75%, nominal input voltage and at rated output load unless otherwise specified. environment approval test parameters conditions shock wave form half sine wave acceleration amplitude 5gn bump duration 30 ms converter operation before and after test, body mounted (on chassis) number of bumps 18 (3 in each direction for every axis) vibration test mode sweep sine displacement 1mm acceleration 3g converter operation 10 - 100hz, speed 0.05hz/s safety specifications parameters standards in formation technology equipment en 60950 - 1:2006+a11:2009 emi - conducted and radiated emission en55011, class b electrostatic discharge immunity iec 61000 - 4 - 2 rf, electromagnetic field immunity iec 61000 - 4 - 3 electrical fast transient/burst immunity iec 61000 - 4 - 4 surge immunity iec 61000 - 4 - 5 rf, conducted disturbance immunity iec 61000 - 4 - 6 power frequency magnetic field immunity iec 61000 - 4 - 8 voltage dips, short interruptions immunity iec 61000 - 4 - 11 information technology equipment ul 60950 - 1:2007 information technology equipment can/csa - c22.2 no.60950 - 1 - 07
preliminary series am el10 -az 10 w att | a c - dc converter www.aimtec.com tel: + 1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052e r8 3 of 3 north america only pin out specifications dimensions top view 1 2 3 4 5 1.05 (0.04) case tolerance 0.50 (0.02) pin diameter 1.0 0.05 (0.04 0.002) pin pitch tolerance 0.35 (0.014) dimensions mm (inch) 5? 1.0 (? 0.04) div: 10.00 (0.40) 56.46 (2.22) 30.86 (1.21) 20.40 (0.80) 5.37 (0.21) 5.37 (0.21) 5.27 (0.21) 5,27 (0.21) 45.72 (1.80) 10.20 (0.40) 10.20 (0.40) 25.10 (0.99) 8.00 (0.31) top view 1 2 3 4 5 note: 1. d atasheets are updated as needed and as such, specifications are subject to change without notice. once printed or downloaded, datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product l abels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4. all specifications are measured at an ambient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other l imited information are considered proprietary and may not be available for release. 6. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control s ystems or other such applications whic h necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. warranty is in accordance with aimtecs standard terms of sale available at www.aimtec.com. pin single 1 ac input (n) 2 ac input (l) 3 +v output 4 - v output 5 no pin
|
